4140 heat treated steel properties Related introduction

  1. SAE AISI 4140 Steel Properties, Material Heat Treatment ...

  2. Technical Information: 4140 HT - SB Specialty Metals

    4140 HT Surface Hardening . 4140 HT is a medium carbon alloy steel heat treated to a . nominal hardness of 28-32 HRC. 4140 HT can also be surface hardened to increase wear resistance . Typical Chemical Composition

  3. 4140HW Alloy Steel Technical Data

    TimkenSteels 4140HW grade is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier cross-sections. You find 4140HW in a variety of bar and tubing applications in quenched and tempered conditions.

  4. AISI 4140 Alloy Steel (UNS G41400) - azom.com

  5. 4140 HIGH TENSILE STEEL - interlloy.com.au

    4140 high tensile steel 4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved

  6. 4140 Alloy Steel Tubing - 4140 Heat Treated Steel Tubing ...

  7. Datasheet for Steel Grades Carbon Steel ASTM 4140

    This page is mainly introduced the ASTM 4140 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of ASTM 4140,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application.

  8. Encore Metals - 4140/4142

  9. 4140 Pre Hard - BICO Steel Service Centers

    4140 Pre Hard 4140PH is a 4140 heat treated steel properties Heat Treatment For specific applications where mechanical properties higher than 34 HRC are required, hardening can be performed in the following way: 4140 heat treated steel properties control of steel temperature uniformity and sufficient holding times to limit stresses and prevent cracking.

  10. Technical Information: 4140 HT - SB Specialty Metals

    4140 HT Surface Hardening . 4140 HT is a medium carbon alloy steel heat treated to a . nominal hardness of 28-32 HRC. 4140 HT can also be surface hardened to increase wear resistance . Typical Chemical Composition

  11. 4140 Hot Rolled Heat Treated Round Bar, Midwest Steel ...

    4140 Hot Rolled Heat Treated Round Bar. 4140 is a widely used medium carbon steel. A general purpose alloy, has good strength, toughness and hardness. Refered to as chromoly steel, due to the inclusion of .95% chromium and .20% molybdenum alloying elements. 4140 Hot Rolled Heat Treated Round Bar

  12. Kromite® #3, HT 4140 Steel, Associated Steel Corporation

    4140/4150 (modified) Hot Roll, Heat Treated, High Strength Alloy. Kromite #3 is a modified 4140/4150 steel. Typical hardness is Rockwell C 28/34. This chromium and molybdenum based alloy is electric furnace melt, vacuum degassed, stress relieved, and machine straightened. It is offered in the hot roll, heat treated condition.Some results are removed in response to a notice of local law requirement. For more information, please see here.

  13. Kromite® #3, HT 4140 Steel, Associated Steel Corporation

  14. 4140 Pre Hard - BICO Steel Service Centers

    Heat Treatment For specific applications where mechanical properties higher than 34 HRC are required, hardening can be performed in the following way: Heating (about 850°C - 1562°F) with a sufficient holding time (1 hour/inch) Water, oil or air quenching depending on thickness (see C.C.T diagram)

  15. 4140 Hot Rolled Heat Treated Alloy Steel On Fay Industries ...

  16. HIGH TENSILE STEEL AISI 4140 - S&T Stainless

    HIGH TENSILE STEEL AISI 4140 AISI 4140 Chrome - Moly High Tensile Steel, generally supplied hardened and tempered to Condition T in sections up to 100mm, with a tensile strength of 850 1000 MPa and aiming for this strength range in larger sections. It offers a very good balance of strength, toughness and wear-resistance.

  17. Heat Treating 4140 steel FAQ : anvilfire.com How-to.

  18. Section R - emjmetals.com

    Properties shown are based on a single heat, selected so that the significant elements are in the middle of the chemical composition limits and incidental elements are at a minimum. Quenched-and-tempered properties are based on treating a .530 round for the hardening grades and a .565 round for the carburizing grades.Some results are removed in response to a notice of local law requirement. For more information, please see here.

Online Consultation