4140 heat treated steel properties Related introduction

  1. SAE AISI 4140 Steel Properties, Material Heat Treatment ...

  2. 4140HW Alloy Steel Technical Data

    TimkenSteels 4140HW grade is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier cross-sections. You find 4140HW in a variety of bar and tubing applications in quenched and tempered conditions.

  3. 4140 Steel & 4150 Steel, Specialty Steel Co.

  4. 4140 HIGH TENSILE STEEL - interlloy.com.au

    4140 high tensile steel 4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved

  5. 4140 Alloy Steel Tubing - 4140 Heat Treated Steel Tubing ...

  6. Technical Information: 4140 HT - SB Specialty Metals

    4140 HT Surface Hardening . 4140 HT is a medium carbon alloy steel heat treated to a . nominal hardness of 28-32 HRC. 4140 HT can also be surface hardened to increase wear resistance . Typical Chemical Composition

  7. Datasheet for Steel Grades Carbon Steel ASTM 4140

    This page is mainly introduced the ASTM 4140 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of ASTM 4140,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application.

  8. 4140 High Tensile Steel, Interlloy, Engineering Steels ...

  9. 4140 Pre Hard - BICO Steel Service Centers

    4140 Pre Hard 4140PH is a 4140 heat treated steel properties Heat Treatment For specific applications where mechanical properties higher than 34 HRC are required, hardening can be performed in the following way: 4140 heat treated steel properties control of steel temperature uniformity and sufficient holding times to limit stresses and prevent cracking.

  10. 4140 Hot Rolled Heat Treated Round Bar, Midwest Steel ...

    4140 Hot Rolled Heat Treated Round Bar. 4140 is a widely used medium carbon steel. A general purpose alloy, has good strength, toughness and hardness. Refered to as chromoly steel, due to the inclusion of .95% chromium and .20% molybdenum alloying elements. Sizes through 7'' comply with ASTM-A193-B7, ASME SA193 Class B7 and/or MIL-S-1222(B7).

  11. Encore Metals - 4140/4142

    Alloy AISI/SAE 4140/ 4142 (UNS G 41400/G 41442) Mechanical Properties Heat treated to HRC 22 maximum for sour gas service. Minimum tempering temp 1150 F. Conforms to NACE Standard MR01-75. Also meets the tensile requirements of L80 as below

  12. Kromite® #3, HT 4140 Steel, Associated Steel Corporation

    4140/4150 (modified) Hot Roll, Heat Treated, High Strength Alloy. Kromite #3 is a modified 4140/4150 steel. Typical hardness is Rockwell C 28/34. This chromium and molybdenum based alloy is electric furnace melt, vacuum degassed, stress relieved, and machine straightened. It is offered in the hot roll, heat treated condition.Some results are removed in response to a notice of local law requirement. For more information, please see here.

  13. Technical Information: 4140 HT - SB Specialty Metals

    4140 HT Surface Hardening . 4140 HT is a medium carbon alloy steel heat treated to a . nominal hardness of 28-32 HRC. 4140 HT can also be surface hardened to increase wear resistance . Typical Chemical Composition

  14. Kromite® #3, HT 4140 Steel, Associated Steel Corporation

  15. 4140 Pre Hard - BICO Steel Service Centers

    Heat Treatment For specific applications where mechanical properties higher than 34 HRC are required, hardening can be performed in the following way: Heating (about 850°C - 1562°F) with a sufficient holding time (1 hour/inch) Water, oil or air quenching depending on thickness (see C.C.T diagram)

  16. 4140 Hot Rolled Heat Treated Alloy Steel On Fay Industries ...

  17. HIGH TENSILE STEEL AISI 4140 - S&T Stainless

    HIGH TENSILE STEEL AISI 4140 - continued WELDING: Readily welded in the annealed condition but avoid when possible if hardened and tempered due to the effect on the mechanical properties. Welding in the nitrided, flame or induction hardened condition is not recommended. HEAT TREATMENT: Forging: Heat to 1150°C Hold till uniform

  18. A2 Technical Data - High Speed Steel, Tool Steel for Sale

    Machinability: 70% of a 1% carbon steel; Heat Treating Instructions Hardening. Critical Temperature: Ac1: 1460°F (793°C) Preheating: Heat at a rate not exceeding 400°F per hour (222°C per hour) to 1150-1250°F (621-677°C) and equalize. Then heat to 1300-1400°F (704-760°C). Austenitizing (High Heat): Heat slowly from the preheat. Furnace or Salt: 1725-1750°F (941-954°C) Soak for 30 minutes for the Some results are removed in response to a notice of local law requirement. For more information, please see here.

Online Consultation