astm a572 grade 55 properties Related introduction

  1. ASTM A572 Grade50,55,60 HSLA Structural Steel Plate-AGICO

    ASTM A572 Specification refers to High-Strength Low-Alloy Steel Plate for structural building, among the 5 steel grades of 42, 50, 55, 60 and 65, Grade 50 is one most common steel in applications where need more strength and less weight, use steel plate of this grade other than ordinary carbon steel will make the steel structure with same steel strength but lighter weight.

  2. ASTM A572 - SSAB

    The ASTM A572 specification is the Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel for plates used in general construction and structural applications. ASTM A572 includes five grades with specified minimum yield strengths of 42, 50, 55, 60, and 65 ksi, respectively.

  3. ASTM A572 Grade 55|A572 Gr.55|A572Gr55 steel plate__Steel ...

    Gangsteel is specialized in supplying ASTM steel plate in A572 Grade 42A572 Grade 42A572 Grade 50A572 Grade 55A572 Grade 60A572 Grade 65 etc.

  4. ASTM A572 Grade 55 vs. Normalized SAE-AISI 4130 ...

    Both ASTM A572 grade 55 and normalized SAE-AISI 4130 are iron alloys. They have a very high 99% of their average alloy composition in common. For each property being compared, the top bar is ASTM A572 grade 55 and the bottom bar is normalized SAE-AISI 4130.

  5. Grade 55 Steel Properties - Portland Bolt

    F1554 Grade 55, as supplied by Portland Bolt, is a low carbon, high alloy steel that we have manufactured to our exacting specifications. Additionally, Portland Bolts F1554 Grade 55 also conforms to supplement S1, which specifies weldable steel.

  6. ASTM A572 Steel, grade 55 - MatWeb.com

    ASTM A572 Steel, grade 55, High-strength low-alloy steel, structural quality

  7. ASTM A572 Grade 55 HSLA Steel :: MakeItFrom.com

    The graph bars on the material properties cards below compare ASTM A572 grade 55 to: wrought alloy steels in the same category (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50

  8. A572 Gr.55 - Steel grades, Properties and Global Standards

    A572 Gr.55 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier: [email protected]

  9. ASTM Standard A572 - INFRA-METALS

    ASTM A572 Structural Steel. One of the most commonly used A572 grades is A572-50. This grade has an ultimate tensile strength of 65,300 psi and a high tensile yield strength of 50,000 psi. It is used in a broad array of structural applications, some of which include buildings, transmission towers, bridges, construction equipment,astm a572 grade 55 properties

  10. A572 Structural, Carbon & HSLA Steel Plate - Chapel Steel

    25 rows · ASTM A572 A high-strength low-alloy steel plate that is utilized in a variety of structural

  11. ASTM A572 Grade 55 vs. Normalized SAE-AISI 4130 ...

  12. Steel grades according to American standards - A36,

    Grade 55 0.25 1.35 0.05 0.04 0.40 astm a572 grade 55 properties Mechanical properties A36 - 04b A36 250 [36] 400-550 [58-80] 20 21 A572 - 04 Grade 42 290 [42] 415 [60] 20 24 Grade 50 345 [50] 450 [65] 18 21 astm a572 grade 55 properties Steel grades according to American standards - A36, A572, A588, A709, A913, A992.

  13. Differences Between ASTM A529 & A572, Hunker

    Mechanical Properties. Mechanically, A572 and A529 are very similar. A572 has an ultimate tensile or breaking strength of 60,200 pounds per square inch, a tensile yield strength of 42,100 psi and a shear modulus of 11,600 ksi. A529 possesses an ultimate tensile strength of 72,500 psi, a tensile yield strength of 42,100 psi and a shear modulusastm a572 grade 55 properties

  14. ASTM A572 Steel, grade 65 - MatWeb.com

    ASTM A572 Steel, grade 65 Categories: Metal; Ferrous Metal; ASTM Steel; Carbon Steel; Low Carbon Steel. Material Notes: High-strength low-alloy steel, structural

  15. FAQ's: Steel Grades- Type of Steel- Steel supplier ...

    The mechanical properties are also known as the physical properties of the specification A572 are determined by combining one of five different Steel grade specifications including Grades 42, 50, 55, 60 and 65, noted after the A572 to establish various Steel strength requirements.

  16. Speedy Metals Information for ASTM A572 Grade 50 Plate

    ASTM A572 Grade 50 Plate. Grade 50 is used in general plate applications when the plate will be riveted, bolted, or welded. Grade 50 is a Columbium-Vanadium steel that offers a minimum yield of 50,000 PSI. In addition, ASTM A572 Grade 50 is noted for its increased resistance to atmospheric corrosion.

  17. F1554 Grade 55 - F1554 Anchor Bolts

    ASTM F1554 grade 55 anchor bolts are manufactured from a modified mild steel that has a higher minimum yield strength (55 ksi) than traditional A36 mild steel (36 ksi). This specification was widely used in the light pole and traffic signal industry long before the ASTM F1554 specification was introduced in 1994 and was commonly referred to as A36M55.

  18. A572 Gr.50 - Steel grades, Properties and Global Standards

    This page cover the A572 Gr.50 chemical element, Mechanical Properties, A572 Gr.50 Datasheet, Cross Reference of A572 Gr.50 steel, Mainly used for .

  19. A572 Grade 55,A572Gr55,A572 Gr 55,steel plate-S355J2 ...

    A572 Gr.55 steel plate is high strength low alloy columbium-vanadium structural steel grade. A 572 Gr.55 steel steel plate are intended for riveted, bolted or welded structural. Compare with A572 Gr.50, A 572 Gr55 steel has a more yield and tensile strength in project.

  20. Steel Plate ASTM A572/A572M Grade 65 60 55 50 42 in

    Steel Plate ASTM A572/A572M Grade 65 60 55 50 42 in Large Stock. Mechanical and chemical properties of ASTM A572 plate

  21. A572 Steel Plate, Precision Grinding, Inc.

    The ASTM A572 carbon steel specification covers the standard requirements for Grades 42, 50, 55, 60, and 65 for high-strength low-alloy columbium-vanadium structural steel shapes, plates and bars for applications in bolted, riveted and welded structures in bridges and buildings.

  22. Tables of Material Properties, MechaniCalc

    The tables below provide properties of common engineering materials. The material property data provided are intended to be representative of the material described. The provided values tend toward the conservative end of the spectrum and could be used as baseline design values for preliminary design.

  23. Steel Plate ASTM A572/A572M Grade 65 60 55 50 42 in

  24. BAR DATA HANDBOOK AISI/SAE - Steel Dynamics

    x Structural Grades ASTM A36 and A572 Grade 50 x Low Alloy Tube and Flange Grades (T2/F2, T11/F11, T22/F22) The grades listed above are a summary of those produced at the Engineered Bar Products facility. Please inquire for grades not listed above or for custom designed grades. Hot-Rolled cut lengths are available between 16 and 40 feet. Steel

  25. SHAPE MATERIAL (ASTM A572 Gr 50 with special

    1. Meet all requirements of ASTM A572/A572M-94c Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel Grade 50; 2. The steel shall be made to a practice producing nitrogen not greater than 0.012% or steel shall be made to a practice producing nitrogen not greater than 0.015% and nitrogen binding elements shall be added;

  26. Material S355 Steel Properties, Comparison, Equivalent ...

  27. steelwise Keeping tabs on ASTM specifications aRE yOU ...

    A572 Grade 50, ASTM A529 Grade 50 or ASTM A992; each of these 50 ksi grades has F y = 50 ksi and F u = 65 ksi for these shapes. The availability of M-shapes in grades other than A36 should be confirmed prior to their specification. M-shapes with a higher yield and tensile strength can be obtained by specifying ASTM A572 Grades 55, 60 and 65 astm a572 grade 55 properties

  28. High-Strength Low-Alloy Steels - ASM International

    High-strength low-alloy steels include many standard and proprietary grades designed to provide specific desirable combinations of properties such as strength, toughness, formability, weld-ability, and atmospheric corrosion resistance. These steels are not consid-ered alloy steels, even though their desired properties are achieved by the

  29. A656 Structural, Carbon & HSLA Steel Plate - Chapel Steel

  30. Technical Bulletin Construction - U.S. Steel

    ASTM A653 applies to HDG-coated steel sheets. ASTM A792 applies to GALVALUME Coated Sheet Steels. Table 2 details requirements for the chemical composition for the heat analysis of all steel designations in A 653 and A 792. For example, Commercial

Online Consultation